Archive for March, 2009

Restless soul

Posted by Bimsan on Sunday, March 29, 2009

Today, it has been an indecisive day. Playing poker for a little while, while crafting, watching TV for a while - no peace in the body.

Strangely enough, poker was good though I am so distracted - but on the other hand, the resistance on my level is not the sharpest so just by playing the pure ABC poker and have average luck, plus it goes.

Busy oneself with my first shaker card. Pink Easter card with a lot of glitter for a little girl go.

Land

Posted by Bimsan on Friday, March 27, 2009

Right now life feels like a big empty hole. Did yesterday's announcement that I have cancer.

Cancer affects just second course - not someone I know and certainly not myself ...

Do not think it really sunk in yet because I am very calm, I who normally are eyed for me to choose between Aftobladet and Expressen. Or is it that now when I really got nothing to worry about taking care of calm.

I reacted, of course, but not the way I expected. Are the most straight up and down, letting the tears flow. No panic as far as the eye can see.

Is now awaiting clearance from Lund, the treatment system to start, was apparently different in endometrial cavity. Must also enter and magnetic x-rayed to ensure that it does not spread (can apparently spread to the lungs, among others).

Borders to CraftRobo / Silhouette

Posted by Bimsan on Sunday, March 22, 2009

Some bands can always be good to have. You can find the GSD file in the " pink files ".

scalloped.png

An Easter card with one of the borders.

easter3.png

Carrier Sheet

Posted by Bimsan on Friday, March 13, 2009

To make its own carrier sheet with the grid for the remnants.

Download Carrier Sheet (196)

You will need:

  • 2 A4 card stock (160-200 gsm)
  • A4 laminating pocket (and of course a laminator)
  • Xyron tape for Workstation with removable adhesive (removable adhesive spray or wide two-way Glue (Zig) works of course)
  • Removable tape

untitled-2.png

Check the following settings in RoboMaster:

File / Document Settings / Use Registration Marks to be bent
File / Output Setting / Print Cut Lines should be bent
Edit / Grid Settings / Grid Spacing shall be 10mm

This is consistent with it may want to check out.

  • Print page and you now have a copy of the screen, with grid, on paper.
  • Laminating a blank paper
  • Glue the printed sheet of what you are laminated
  • Tape the edges where the rollers will go with the removable tape
  • Run the whole package of Xyron or spaya with removable adhesive
  • Remove the removable tape
  • Dutta, eg kökshanduk one if it appears to the sticky

Voila, the world's best Carrier Sheet, where you can place small pieces of paper exactly.

Here's my out (accidentally put it upside down on nystämplat :) ) That would be done for istf inches. metrics.

carrier

Envelope

Posted by Bimsan on Friday, March 13, 2009

New file to CraftRobo / Silhouette - a small envelope of approximately 8 × 6 cm. The words "Congratulations" is included. You'll find it in the " pink files ".

kuvert.png

New page

Posted by Bimsan on Friday, March 13, 2009

Have now a new page containing all cut files (GSD, GRA) with image. Downloads are previously a sorted list of all files to be downloaded - GSD, GRA, PDF, etc.

New photos

Posted by Bimsan on Thursday, March 12, 2009

Now I have finally managed to scan some new cards. Succeeded is perhaps to exaggerate - crooked and reel, they were but anyway ...

bikupa.png [Singlepic id = 218 w = 320 h = 240 float =]


easter1.png [Singlepic id = 216 w = 320 h = 240 float =]


rose1.png [Singlepic id = 214 w = 320 h = 240 float =]

Sweepstakes stamps

Posted by Bimsan on Thursday, March 12, 2009

Hobbies and Crafts raffle ATC stamps from Tim Holtz. Hurry up there and take a lot :)