Swede Design

Made a little video how you cut out the SVG files directly to the Craft Robo / Silhouette from Inkscape instead of saving as DXF and import into RoboMaster.

Now, I have tried to cut out the grunge paper with the help of Robban (CraftRobo) and it was brilliant!

Grunge paper I bought at Country Token . Cut out with three passports with pressure 30, embossed with fish embossingplatta, colored with distress inks (fired brick) and then a little cosmic shimmer (Copper rose sparkle from Joanna Sheen ). The colors are ideal for Basic Grey Eskimo Kisses series.

Found some other goodies in Country also Token. Tim Holz 'Mask blanks sheets "which also worked to cut out with Robban. The glue was for some reason weaker than in the finished masks but there is no removable glue can not fix so it worked out.

Then there was the glass accession cream (wow, that word) too. Works perfectly.

Examples of masks and etching will certainly up over time.

Quickutz has made an addition to paper thickness in gsm instead of lbs. You will find the Appendix here .

When you install and run it, you get the following box where you select GSM (UK)

Then you make two lists, one with no installed paper thicknesses and one of those installed. Here's how it looked at me.

And after I cleaned, I have them, that is only paper I know - yay!

Silhouette CraftRobo and use the same software, so even if the file is from Quikutz it works great with CraftRobo.

Paper thickness you already have will not go away!

Been working together a little ant You'll find it for cutting files .

A little cream may be needed in the summer heat Have been using corrugated pattern characterized author of the form in my example and a little glitter chocolate topping - yummy!

A yummy low fat cake that I have pulat together today. So nice to not sleep all day! Do not cut out "glare" to the berry if you have not really sharp knife, but the plot with a white pen instead (or skip it entirely).

A little tip on how I cut out shapes with multiple colors.

Cut into smaller pieces and place on cutting mat (available in file size)

Not sure if it fits "cut out" with pencil first.

That's it!

Some bands can always be good to have. You can find the GSD file in the " pink files ".

An Easter card with one of the borders.

To make its own carrier sheet with the grid for the remnants.

Download Carrier Sheet (192)

You will need:

• 2 A4 card stock (160-200 gsm)
• A4 laminating pocket (and of course a laminator)
• Xyron tape for Workstation with removable adhesive (removable adhesive spray or wide two-way Glue (Zig) works of course)
• Removable tape

Check the following settings in RoboMaster:

File / Document Settings / Use Registration Marks to be bent
File / Output Setting / Print Cut Lines should be bent
Edit / Grid Settings / Grid Spacing shall be 10mm

This is consistent with it may want to check out.

• Print page and you now have a copy of the screen, with grid, on paper.
• Laminating a blank paper
• Glue the printed sheet of what you are laminated
• Tape the edges where the rollers will go with the removable tape
• Run the whole package of Xyron or spaya with removable adhesive
• Remove the removable tape
• Dutta, eg kökshanduk one if it appears to the sticky

Voila, the world's best Carrier Sheet, where you can place small pieces of paper exactly.

Here's my out (accidentally put it upside down on nystämplat ) That would be done for istf inches. metrics.

New file to CraftRobo / Silhouette - a small envelope of approximately 8 × 6 cm. The words "Congratulations" is included. You'll find it in the " pink files ".

Have now a new page containing all cut files (GSD, GRA) with image. Downloads are previously a sorted list of all files to be downloaded - GSD, GRA, PDF, etc.